Happymodel Mobeetle6 65mm 1S AIO F4 Flight Controller Built-in OPENVTX Whoop and Toothpick 2in1 FPV Racing Drone BNF w/ SE0702 23000KV Motor
$118 – Check latest price on: AliExpress, Amazon DE, Banggood
| Happymodel Mobeetle6 Specifications |
| Brand |
Happymodel |
| Model |
Mobeetle6 |
| Wheelbase |
65mm |
| Size |
80mm*80mm*30mm |
| Weight |
17.5g (without battery) |
| Motor |
| Mode |
SE0702 KV23000 |
| Configu-ration |
9N12P |
| Stator Diamter |
7mm |
| Stator Length |
2mm |
| Shaft Diameter |
Φ1mm |
| Motor Dimension(Dia.*Len) |
Φ9.5mm*14mm |
| Weight |
1.5g |
| No.of Cells(Lipo) |
1S only |
| Propeller |
| Material |
PC |
| Pitch |
1 inch |
| Props Dia |
30mm |
| Center Hole Dia |
1mm |
| Weight |
0.19g |
| Flight controller |
| DiamondF4 ELRS FC Firmware Target |
CrazybeeF4SX1280(ELRS SPI RX version) |
| DiamondF4 FR FC Firmware Target |
CrazybeeF4FR(Frsky SPI RX version) |
| MCU |
STM32F411CEU6 (100MHZ, 512K FLASH) |
| Sensor |
MPU-6000 or ICM20689 or BMI270(SPI connection) |
| Power Supply |
1S battery input (DC 2.9V-4.35V) |
| Built-in |
5A(each) Blheli_S 4in1 ESC Dshot600 ready
Betaflight OSD(SPI Control)
5.8G OPEN VTX
SPI ELRS V2.0/Frsky receiver
5V 1A BEC |
| Original whoop size compatible |
YES |
| Onboard 4in1 ESC |
| MCU |
upgraded to EFM8BB21 |
| Power Supply |
1S LiPo/LiPo HV |
| Current |
5A continuous peak 6A (3 seconds) |
| Factory Firmware |
O_H_50_REV16_8.HEX |
| Default Protocol |
DSHOT600 |
| BLHeliSuite Programmable |
Support |
| Onboard SPI ExpressLRS 2.4GHz Receiver |
| Packet Rate Option |
50Hz/150Hz/250Hz/500Hz |
| ExpressLRS Firmware Version |
V2.0 |
| RF Frequency |
2.4GHz |
| Antenna |
Enameled copper wire antenna |
| Telemetry Output Power |
<12dBm |
| Receiver Protocol |
SPI ExpressLRS |
| Compatible with ExpressLRS V2.0 TX Module |
Yes |
| Couldn’t Flash Separately ExpressLRS Firmware |
Yes |
| Onboard Frsky SPI D8 receiver Version |
| Compatible SPI BUS receiver Frsky D8 |
Yes |
| Compatible Non EU Transmitter D8 Model |
Yes |
| Channels |
8CH |
| Resolution |
1cm |
| Failsafe Support |
Yes |
| No Ground Interference(Transmitter and receiver 1 m from the ground) |
200m~300m |
| Onboard 5.8g OPENVTX |
| Firmware Version |
OPENVTX |
| Smartaudio |
v2.1 |
| PIT Mode Support |
Yes |
| RCE Mode Support |
Yes |
| Channels |
48CH |
| Transmitting Power |
0/RCE/25mw/100mw/400mw |
| Power Supply |
DC 5V |
| Current (5v) |
<650ma (400mw) |
| Runcam Nano 3 Specs |
| Model |
RunCam Nano 3 |
| Image Sensor |
1/3″ CMOS |
| Horizontal Resolution |
800TVL |
| Lens |
2.3mm(M6.5) FOV 140° |
| Signal System |
NTSC |
| S/N Ratio |
>50dB |
| Electronic Shutter Speed |
Auto |
| Auto Gain Control (AGC) |
Auto |
| Min. Illumination |
0.01Lux@1.2F |
| D-WDR |
Auto |
| Day/Night |
Color |
| Power |
DC 3-5.5V |
| Current |
110mA@5V 120mA@3.3V |
| Housing Material |
ABS |
| Dimensions |
L14mm*W14mm*H9mm |
| Net Weight |
1.2g |
| Lipo Battery |
| Capacity |
300mAh |
| Voltage |
3.8V |
| Continuous Discharge Rate |
30C |
| Connector |
PH2.0 |
| Size |
57mmx12mmx7mm |
| Weight |
7.5g |
Happymodel Mobeetle6 Features:
- Comes with tooth pick frame for convert
- The lightest 1S Whoop and Toothpick 2-IN-1 fpv drone
- Powerful and efficiency
- Built-in OPENVTX up to 400mw
- The lightest 1s AIO 5IN1 F4 flight controller
- New Unibell SE0702 brushless motors with pcb wire board
- Low profile Canopy design
Check lowest price of Happymodel Mobeetle6:
